Clutch Bolt

Topic locked

#8912 by simmscity
Fri May 20, 2011 3:37 pm

Im attempting to take apart my clutch so that I may instal my new contra spring for my yerf dog 3206. However Im having a problem figuring out the size socket I need. Thanks

Heavy duty ball joints, Generation III spindles
3" Front suspension lift, Stage 2 rear shocks
4/110m hubs w/18" wheels in front
10g rollers w/ 15000 power spring
[u]BDX Stage 1 engine upgrade [/u]

[b]Sgt. Simms, Jeremy
USMC[/b]

Username

simmscity

Rank

Enthusiast

Posts

32

Joined

Tue Feb 22, 2011 2:37 am

Re: Clutch Bolt

#8913 by JES
Fri May 20, 2011 10:12 pm

Here's a link to the install guide: How-to: Install The STAGE 1 Drivetrain Package

__________________________________________________________________________

[b]YERF DOG 3206 GX150 (red)[/b]
[i]BDX CDI Upgrade & High Output Ignition Coil, High-Flow Uni Air Filter Intake Kit, K&N Pre Filter
Koso 115mm Teflon Variator, High-Stall Clutch Unit, Yellow 1500 rpm spring, 10g rollers
BDX Heavy Duty Balljoints, Reinforced Front Bulkhead & A-Arms, BDX LIFETIME 3rd Gen Spindles
BDX S2 FRONT Shocks +3 inch Lift, BDX S2 Rear shocks
11-pole Stator Plug & Play Kit, Upgraded Battery, 5-Yerf Dog Lights (wired with relay)
Mikuni Carburetor VM26-606, Solid Aluminum Intake Manifold, Header Wrap Kit
Front Brake Retrofit Kit
MudTrak - 23x7x10 Front Tires & Rims, MudTrak 22x11X10 Rear Tires & Rims
LED brake lights[/i]

Username

JES

Rank

Newbie

Posts

20

Joined

Sun Apr 10, 2011 7:36 am

Re: Clutch Bolt

#8914 by simmscity
Sat May 21, 2011 8:29 pm

i appreciate the link but it doesnt tell you the size of the nut i am refering to. the one more specificly refering to is the one directly on top of the clutch keeping the clutch spring and pulley all held together. it is a flat bolt as well. if that helps.

Heavy duty ball joints, Generation III spindles
3" Front suspension lift, Stage 2 rear shocks
4/110m hubs w/18" wheels in front
10g rollers w/ 15000 power spring
[u]BDX Stage 1 engine upgrade [/u]

[b]Sgt. Simms, Jeremy
USMC[/b]

Username

simmscity

Rank

Enthusiast

Posts

32

Joined

Tue Feb 22, 2011 2:37 am

Re: Clutch Bolt

#8917 by JES
Sun May 22, 2011 10:44 pm

I believe it's 38mm.

Can anyone else verify or correct this?

__________________________________________________________________________

[b]YERF DOG 3206 GX150 (red)[/b]
[i]BDX CDI Upgrade & High Output Ignition Coil, High-Flow Uni Air Filter Intake Kit, K&N Pre Filter
Koso 115mm Teflon Variator, High-Stall Clutch Unit, Yellow 1500 rpm spring, 10g rollers
BDX Heavy Duty Balljoints, Reinforced Front Bulkhead & A-Arms, BDX LIFETIME 3rd Gen Spindles
BDX S2 FRONT Shocks +3 inch Lift, BDX S2 Rear shocks
11-pole Stator Plug & Play Kit, Upgraded Battery, 5-Yerf Dog Lights (wired with relay)
Mikuni Carburetor VM26-606, Solid Aluminum Intake Manifold, Header Wrap Kit
Front Brake Retrofit Kit
MudTrak - 23x7x10 Front Tires & Rims, MudTrak 22x11X10 Rear Tires & Rims
LED brake lights[/i]

Username

JES

Rank

Newbie

Posts

20

Joined

Sun Apr 10, 2011 7:36 am

Re: Clutch Bolt

#8921 by JES
Wed May 25, 2011 2:28 pm

I stand corrected. After physically trying the socket myself, it's definetly not 38mm...

Either 40mm or 1 1/2". I'll try and verify it tomorrow.

Last edited by JES on Thu May 26, 2011 9:12 pm, edited 1 time in total.

__________________________________________________________________________

[b]YERF DOG 3206 GX150 (red)[/b]
[i]BDX CDI Upgrade & High Output Ignition Coil, High-Flow Uni Air Filter Intake Kit, K&N Pre Filter
Koso 115mm Teflon Variator, High-Stall Clutch Unit, Yellow 1500 rpm spring, 10g rollers
BDX Heavy Duty Balljoints, Reinforced Front Bulkhead & A-Arms, BDX LIFETIME 3rd Gen Spindles
BDX S2 FRONT Shocks +3 inch Lift, BDX S2 Rear shocks
11-pole Stator Plug & Play Kit, Upgraded Battery, 5-Yerf Dog Lights (wired with relay)
Mikuni Carburetor VM26-606, Solid Aluminum Intake Manifold, Header Wrap Kit
Front Brake Retrofit Kit
MudTrak - 23x7x10 Front Tires & Rims, MudTrak 22x11X10 Rear Tires & Rims
LED brake lights[/i]

Username

JES

Rank

Newbie

Posts

20

Joined

Sun Apr 10, 2011 7:36 am

Re: Clutch Bolt

#8926 by JES
Thu May 26, 2011 9:11 pm

Regretfully, the nut on my clutch was rounded from the previous owner changing out the clutch at some point. After some searching, I've read that it is 1 1/2".

I needed a large cresent wrench and a vice to get mine apart.

While I had it apart, I added the High-Stall Clutch Unit and a 1500 RPM contra spring. I also added the KOSO 115mm Variator with 10g roller weights and a new Kevlar CVT drive belt. 8)

__________________________________________________________________________

[b]YERF DOG 3206 GX150 (red)[/b]
[i]BDX CDI Upgrade & High Output Ignition Coil, High-Flow Uni Air Filter Intake Kit, K&N Pre Filter
Koso 115mm Teflon Variator, High-Stall Clutch Unit, Yellow 1500 rpm spring, 10g rollers
BDX Heavy Duty Balljoints, Reinforced Front Bulkhead & A-Arms, BDX LIFETIME 3rd Gen Spindles
BDX S2 FRONT Shocks +3 inch Lift, BDX S2 Rear shocks
11-pole Stator Plug & Play Kit, Upgraded Battery, 5-Yerf Dog Lights (wired with relay)
Mikuni Carburetor VM26-606, Solid Aluminum Intake Manifold, Header Wrap Kit
Front Brake Retrofit Kit
MudTrak - 23x7x10 Front Tires & Rims, MudTrak 22x11X10 Rear Tires & Rims
LED brake lights[/i]

Username

JES

Rank

Newbie

Posts

20

Joined

Sun Apr 10, 2011 7:36 am

Re: Clutch Bolt

#9075 by simmscity
Fri Aug 05, 2011 1:41 pm

Thanks for your help. I did the same thing utilizing the vise and a large vise grip and a rubber mallet.

Heavy duty ball joints, Generation III spindles
3" Front suspension lift, Stage 2 rear shocks
4/110m hubs w/18" wheels in front
10g rollers w/ 15000 power spring
[u]BDX Stage 1 engine upgrade [/u]

[b]Sgt. Simms, Jeremy
USMC[/b]

Username

simmscity

Rank

Enthusiast

Posts

32

Joined

Tue Feb 22, 2011 2:37 am

Topic locked

Page 1 of 1
7 posts