Green Web Hosting! This site hosted by DreamHost.  
Online Store - Parts for GY6 Yerf Dog Blade Twister Hammerhead Carter Talon
The Buggy Depot Tech Center contains technical information regarding Yerf-Dog, Blade, Twister Hammerhead and many more 150cc buggies.
Buggy Depot Site Map
Buggy Depot - Off Road Buggy Forum! Click to enter!
BuggyDepot.com Tech Center - 150cc GY6 Knowledgebase! Yerf Dog, Twister Hammerhead, Tomberlin Crossfire, Carter Talon...
BuggyDepot.com Tech Center 2.0
 
Categories:
All Articles [23]
Maintenance & Troubleshooting [3]
BDX Install Guides [6]
GY6 Performance Advice [3]
Service Manuals [0]
How It Works! Writeups [5]
General GY6 Information [4]
Weaknesses & Fixes [1]
Modification Ideas [0]
BuggyDepot News
 
BuggyDepot.com December 2009 Newsletter
Wednesday, December 9, 2009
All Crossfire 150R Parts In Stock!
Friday, October 9, 2009
Yerfer .net Content Available On BD!
Tuesday, March 24, 2009
Slow Loading Times Today 3/23/09
Monday, March 23, 2009
Website Downtime 3/17/09
Wednesday, March 18, 2009
Please note...
 
Content is copyright © 2005 - 2010 Buggydepot.com
BDX DIAMOND-PLATE FENDER KIT INSTALL GUIDE [3,375 views]
 
A diagram and description for installing the BDX Diamond-Plate Fender Kit on the Yerf Dog GX150.
BDX Diamond-Plate Fender Kit Install Guide
[3,375 views - 1 comments - Rating 5/5 ***** ]

Fender Kit Installation:


A. Checking the parts.

1. Open up the box of parts and check to make sure the following was included:


2x Front Fenders (Driver side/Passenger side)

2x Rear Fenders (Driver side/Passenger side)

2x Front mount bracket assemblies

4x 1.5" clamps

2x 4" shanks for upper rear mount w/ 3 nuts each

2x 1-1/8" u-clamps

4x 4" Rubber isolation tape pieces


2. If a small part is missing (nut, washer, etc.), it may have possibly come loose during shipping and traveled into the packing materials. Please check the box thouroughly.


B. Mounting the rear fenders.

1. Mount the two rear clamp assemblies on the bar below the rear cargo rack, use the rubber isolator between clamp and frame.
Please refer to attached diagram for positioning.

2. Remove third nut from rear clamp and insert threaded shaft into the corresponding hole in the rear fender. Re-attach nut to shaft, under fender.

3. Attach U-bolts.

4. Adjust rear fenders to desired position.


C. Mounting the front fenders.

1. Mount front clamp assemblies to the frame section above the front tire, use the rubber isolator between clamp and frame.

Note: Please be careful when tightening the clamps. The clamps will break if over tightened! These clamp mounts were selected to break away if the fenders are impacted by an object (tree, etc.) while riding. This will protect the fender from being damaged on impact.




2. Remove bolt (with two yellow-zinc washers) from assembly. Mount fender with this bolt - a washer on each side of fender.

3. Adjust per attached diagram.




D. Check tightness

1. Rear fenders should have no movement or play.

2. Front fenders should feel solid when pressed down, only moving from play between rubber isolator and clamp.

This article has been downloaded 3,375 times
1 comments about this article:
Poster #1 [02/26/10] Rating: Rating 5/5 *****
Will these fenders install and work on buggies other than the Yerf???
Write a comment:
Are you a human? Type "yes":



You can rate this article without commenting...
Just select your rating and leave the comments form blank!
 
--